STANFORD RESEARCH SYSTEMS LDC500 CALIBRATION and STANFORD RESEARCH SYSTEMS LDC500 REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the STANFORD RESEARCH SYSTEMS LDC500 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Laser Diode Controller?
Shop for Comparable Products on our  used Laser Diode Controller page

 
   STANFORD RESEARCH SYSTEMS LDC500   Description / Specification:    
STANFORD RESEARCH SYSTEMS LDC500 100 mA Laser Diode Controller

The SRS LDC500 Laser Diode Controller is an ideal instrument for controlling the current and temperature of your laser diodes. It has the performance and features you expect from instruments costing twice as much. The LDC500 has up to 100 mA of output current with less than 0.3 µA of rms noise. The SRS LDC500 is a 36 W high-precision temperature controller with standard computer interfaces, including Ethernet. It has multiple laser diode protection features, including slow start turn-on, adjustable current limits, and adjustable compliance voltage. Specifications. Current Source Range: 0 to 100 mA, 0 to 50 mA. Setpoint resolution: 1 µA. Accuracy: ±0.02 % of full scale. Output impedance: >1 M-ohm (DC). Thermal Stability: <10 ppm/°C. Noise (10 Hz to 1 MHz): 0.9 µA rms (high range / high BW), 0.9 µA rms (high range / low BW), 0.5 µA rms (low range / high BW), 0.3 µA rms (low range / low BW). Compliance voltage Range: 0 to 10 V, programmable. Resolution: 10 mV. Accuracy: 0.2 V. Monitor Photodiode Bias voltage: 0 to 5 V, programmable. PD current range: 0 to 5,000 µA. Temperature Control range: IC sensor -55 °C to +150 °C, Resistor sensor -150 °C to +250 °C (10 ohm to 500 k-ohm). Setpoint resolution Temperature: 0.001 °C. TEC Output Source type: Linear, bipolar current source. Current range: -4.5 A to +4.5 A.



 

Standard Calibration $285.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the STANFORD RESEARCH SYSTEMS LDC500. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Amplified Spontaneous Emission Source (ASE)
ASE, a process where spontaneously emitted radiation (luminescence) is amplified. In lasers and particularly in high-gain erbium-doped amplifiers, amplified spontaneous emission is usually an unwanted effect. It tends to limit the gain achievable in a single stage of a fiber optic amplifier to the order of 40–50 dB.

Dynamic Range
In a transmission system, the ratio of the overload level to the noise level of the system, usually expressed in dB. Ratio of the highest to lowest detectable signal of a system, expressed in dB.

Optical Power
Optical Power is usually measured in "dBm", or decibels referenced to one miliwatt of power. while loss is a relative reading, optical power is an absolute measurement, referenced to standards. You measure absolute power to test transmitters or receivers and relative power to test loss.

Relative Wavelength Accuracy
When randomly changing the wavelength and measuring the differences between the actual and displayed wavelengths, the relative wavelength accuracy is ± half the span between the maximum and the minimum value of all differences.

Wavelength
Wavelength is a term for the color of light, usually expressed in nanometers (nm) or microns (m). In Fiber Optics the wavelenghts mostly used are in the infrared region where the light is invisible to the human eye.

Please contact us for your STANFORD RESEARCH SYSTEMS LDC500 CALIBRATION and/or STANFORD RESEARCH SYSTEMS LDC500 100 mA Laser Diode Controller REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: